Sketch a diagram of a 4-bit asynchronous counter using a suitable flip-flop. Sketch a timing diagram.

A three-phase transformer having a line voltage ratio of 0.4 kV/11kV is connected Star/Delta and protective transformers on the 0.4 kV side have a current ratio of 500/5. Calculate the ratio of ... on the 11 kV side. Draw a neat circuit diagram and indicate the given values at appropriate places.

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

Draw the circuit diagram of battery charger using SCR and explain its working.

View solution

0 like 0 dislike

1 view 0 answers

in Electrical Engineering

Draw logic diagram of 4:1 multiplexer & give its truth table.

View solution

0 like 0 dislike

1 view 0 answers

in Electrical Engineering

What is the function of a programmable delay line in timing circuits?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

What is the purpose of a GNSS simulator in testing timing systems?

View solution

0 like 0 dislike

1 view 0 answers

in Electrical Engineering

How does a capacitor influence the timing in an RC circuit?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

What is the purpose of a frequency counter in signal measurement?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

What is the function of a frequency counter?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

What is the purpose of a frequency counter?

View solution

0 like 0 dislike

2 views 0 answers

in Electrical Engineering

What is the purpose of a binary counter?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

What is a frequency counter?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

What is the difference between a Johnson counter and a ring counter?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

How does a ring counter work?

View solution

0 like 0 dislike

1 view 0 answers

in Electrical Engineering

Explain the concept of holdover in timing systems.

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

How does an antenna distribution system work in timing networks?

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

What is the difference between timing analysis and state analysis?

View solution

0 like 0 dislike

1 view 0 answers

in Electrical Engineering

A motor has to exert power starting from zero and rising uniformly to 150 HP in 8 mins after which it works at constant power of 100 HP for 5 mins. The motor remains on no load for next 5 mins. The cycle again starts and repeats indefinitely. Determine suitable size of motor.

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

A uniform illumination of 150 lux is to be obtained on the floor of a room measuring 15m x 15m by arranging electric lights suitably. Calculate the number of lamps and wattage of each lamp if lamp efficiency is 20 lumens/watt. Assume and write suitable values of constants required for this calculation.

A uniform illumination of 150 lux is to be obtained on the floor of a room measuring 15m x 15m by arranging electric lights suitably. Calculate the number of lamps and wattage of each ... lamp efficiency is 20 lumens/watt. Assume and write suitable values of constants required for this calculation.

View solution

0 like 0 dislike

0 views 0 answers

in Electrical Engineering

Why is a cycloconverter suitable for low frequency?

Why is a cycloconverter suitable for low frequency?
Answer : A cycloconverter is suitable for low-frequency applications because it can directly convert a high-frequency AC supply to a lower-frequency output without using an intermediate DC stage. Here's ... way of stepping down the frequency while maintaining a good waveform for sensitive loads like motors....

View solution

0 like 0 dislike

2 views 1 answer